- Metal components are fully hot dipped galvanized, hub is zinc plated – Will not rust – No need for painting or special coating for up to 50 years under normal conditions
- Raptor carbon fiber blades withstand 125 mph – Guaranteed for a lifetime, not to break under normal use.
- The permanent magnet generator has a 28 rare earth magnet rotor inside and our skewed stator core for easy turning – up to 2000 watts max output!
- The Missouri Freedom II Wind Turbines have a cut-in wind speed of 6 MPH and NO COGGING!
- Each Freedom PMG rotor contains twice as much copper than any Delco style PMA – more copper means more power!
This unit comes with:
Freedom ll PMG (PERMANENT MAGNET GENERATOR) WITH 28 MAGNET ROTOR
Freedom ll PMG has no brushes, very dependable
125,000 hours + of rated bearing life
Two heavy duty bridge rectifiers for converting 3 phase to dc output
Mounting Bracket and Heavy Duty 2 arms tail assembly
Tail fin measures 29″ tall for maximum tracking
No slip rings to fail or replace. Wire tension system
Comes with 11 Raptor nylon carbon fiber composite blades
Aerodynamically tapered Genuine RAPTOR GENERATION 4 Blades for maximum output
Blades Make 62 1/2″ dia. swept area
Steel blade hub is 1/4” thick x 9” in diameter
Mounting Bracket Fits on 1.5″ schedule #40 or #80 pipe
Heavy duty Hub spacer/stabilizer
3 YEAR Limited WARRANTY
Turbine Weight: 50 pounds
Shipping Weight: 55 pounds
Shipping Dimensions: 30″ x 10″ x 8″
Manufactured in the USA
PMG Features:
NO COGGING – CUT-IN SPEED IS 6 MPH
17 mm Stainless steel shaft compatible with all Missouri Wind and Solar hubs
Polished aluminum case
Zinc plated 28 magnet rotor and skewed stator core
For charging 12, 24, or 48 volt battery banks
Specifically designed for wind turbines
AZN.M1.0
- NO COGGING, easy to turn – Cut in speed of 6 MPH
- Skewed stator core with high grade electrical steel and heavy duty copper windings
- 17 mm stainless steel shaft compatible with all Missouri Wind and Solar hubs
- 2x thick polished aluminum case
- Fits delco bolt patterns and mounts up to our standard mounting bracket
If you are using the PMG on a 12 volt system choose the 12/24v model. For 24 volt systems use 24/48v model. For 48 volt systems use the 48/96v model.
Our Freedom II PMG permanent magnet generator is specifically designed for wind turbine use and can even be used with vertical axis wind turbines (VAWT).
Operating Information:
Produces battery voltage at approximately 266 RPM in parallel; 133 RPM in series
Produces twice (2x) the battery voltage at approximately 506 RPM in parallel; 253 RPM in series
Produces four times (4x) the battery voltage at approximately 960 RPM in parallel; 480 RPM in series
This permanent magnet generator works best with our 9 Blade Raptor Generation 4 blades and hub or our new Falcon Mach 4 80″ 3 blade set.
Why buy a Freedom or Freedom II PMG over a Delco car alternator PMA? The answer is more copper. Copper equals more power – each Freedom PMG stator contains twice as much copper than a Delco style PMA. Some modified alternators use power to make power. Freedom PMGs use no input power. PMAs use a thin aluminum housing and the stator is not pressed in.
The Freedom PMG features a very thick aluminum housing and a pressed in stator that helps with proper alignment and durability. PMAs have only two mounting holes. The Freedom PMG has four of them bolted tightly against the mounting bracket for secure mounting. Alternators and some PMAs have a weak rear bearing. The Freedom PMG utilizes two heavy duty bearings. Most car alternators and PMAs that are re-purposed use low grade/high iron electrical steel which can create a lot of heat. The Freedom PMG uses high grade electrical steel and is optimized for efficient cooling
PMG Features: Comes with two heavy duty rectifiers & one hub spacer stabilizer
Zinc plated 28 rare earth neodymium magnet rotor
For charging 12, 24, or 48V battery banks