Maximumstore 2-90 Amp PMA Rectifiers for Wind Turbine Generator Permanent Magnet alternator
- Works in environments with little or no air movement and features a heavy aluminum body
- Improved temperature and power cycling
- Easy to mount with 2 fixing holes
- Works for single or 3-phase AC to DC wind turbines
- Continuous duty, can handle 90 amps continuously using air cooling
3-Phase Diode Bridge Rectifier: 90 Amp, 1000 Volt.
Convert your three phase current input into DC with this brand new and unused, high quality 90 Amp bridge rectifier which is for use in a wide variety of applications.
Benefits:
Works in environments with little or no air movement and features a heavy aluminum body
Improved temperature and power cycling
Easy to mount with 2 fixing holes
Works for single or 3-phase AC to DC wind turbines
Continuous duty, can handle 90 amps continuously using air cooling
Will accept large cable
Specifications:
Amps: 90A
Voltage: 1000V
Dimensions: 3.8 x 2.4 X 1.1 inches / 97mm x 60mm x 28mm
Fixing hole diameter: 5mm
(PG #12) MDS 100A 1600V Bridge Rectifier for Wind Turbine Generator PMA 3 Phase AC to DC
- MDS
- 100 Amps 1600 volts
- Three Phase Bridge Rectifier
- MDS 100-16
- Package of 1 Rectifier Diode with Hardware per Order
Three Phase Bridge Rectifier 1600V 100A MDS100-16 Package of One Rectifier with hardware per Order
SQL100A 1600V 3 Phase Bridge Rectifier Module Diode 5 Pins For Wind Generator
Description:
SQL100A 1600V 3 Phase bridge rectifier module diode 5 pins fits for wind generator.
Specification:
Model: SQL100A-1600V
Type: 3-Phase Bridge Rectifier Module
Size: 98x58x55mm / 3.86×2.28×2.16″
Output Current: 100A
Repetitive Peak Reverse Voltage(VRRM): 100~1600V
Repetitive Peak Inverse Current(IRRM): 7mA
Isolation Voltage(Viso): 2500V
Storage Temperature(Tstg): -40-125℃
Max. Junction Temperature(Tjm): 150℃
Maximum Forward Voltage(VFM): 1.4V
Phase: 3-Phase
Terminals: 5
Applications:
DC Current Equipment
Soft Start Capacitor
PWM Inverter Rectifier
Inverter Welding Machine
Current Charging Power Supply
Features:
– Vacuum protection welding technology.
– Welding structure, excellent temperature characteristics and power cycle capacity.
– Easy to install, easy to use and maintenance.
– The maximum working temperature of 150 ℃.
– This bridge rectifier can be used in a wide variety of applications.
Package Included:
1 x SQL100A-1600V 3-Phase Bridge Rectifier Module
3 Phase Brake Switch with Rectifier for Wind Turbine Generator
- weather resistant made to be put indoor or outdoor
- 50 AMPS
- designed specifically for 3 phase turbines
- Great with single phase A/C turbines as well as D/C turbines
3 phase brake switch is weather resistant made to be put indoor or outdoor. Although it was designed specifically for 3 phase turbines it works Great with single phase A/C turbines as well as D/C turbines. Works on all AC wind turbines that produce 50 AMPS or less. Switch must face down to keep water out of the box. It works great with grid tie inverters and gives you the ability to shout down your turbine in saver storms. Equipped with mc4 connectors and a billet in aluminum heat sink.
Missouri Wind and Solar Freedom II PMG 12/24 Volt Permanent Magnet Wind Turbine Generator
- NO COGGING, easy to turn – Cut in speed of 6 MPH
- Skewed stator core with high grade electrical steel and heavy duty copper windings
- 17 mm stainless steel shaft compatible with all Missouri Wind and Solar hubs
- 2x thick polished aluminum case
- Fits delco bolt patterns and mounts up to our standard mounting bracket
If you are using the PMG on a 12 volt system choose the 12/24v model. For 24 volt systems use 24/48v model. For 48 volt systems use the 48/96v model.
Our Freedom II PMG permanent magnet generator is specifically designed for wind turbine use and can even be used with vertical axis wind turbines (VAWT).
Operating Information:
Produces battery voltage at approximately 266 RPM in parallel; 133 RPM in series
Produces twice (2x) the battery voltage at approximately 506 RPM in parallel; 253 RPM in series
Produces four times (4x) the battery voltage at approximately 960 RPM in parallel; 480 RPM in series
This permanent magnet generator works best with our 9 Blade Raptor Generation 4 blades and hub or our new Falcon Mach 4 80″ 3 blade set.
Why buy a Freedom or Freedom II PMG over a Delco car alternator PMA? The answer is more copper. Copper equals more power – each Freedom PMG stator contains twice as much copper than a Delco style PMA. Some modified alternators use power to make power. Freedom PMGs use no input power. PMAs use a thin aluminum housing and the stator is not pressed in.
The Freedom PMG features a very thick aluminum housing and a pressed in stator that helps with proper alignment and durability. PMAs have only two mounting holes. The Freedom PMG has four of them bolted tightly against the mounting bracket for secure mounting. Alternators and some PMAs have a weak rear bearing. The Freedom PMG utilizes two heavy duty bearings. Most car alternators and PMAs that are re-purposed use low grade/high iron electrical steel which can create a lot of heat. The Freedom PMG uses high grade electrical steel and is optimized for efficient cooling
PMG Features: Comes with two heavy duty rectifiers & one hub spacer stabilizer
Zinc plated 28 rare earth neodymium magnet rotor
For charging 12, 24, or 48V battery banks
Yosoo 12V 300W Wind Turbine Generator Charge Controller Wind Generator Rectifier Portable Wind Charge Controller (Three Phase)
- Material. The Wind Generator Controller is made of high quality material for long durability and stable performance
- Function. It can protect the wind generator and prevent the battery from overcharging
- To control the charge of wind turbine generator battery
- Easy to install and convenient to use
- Single phase and three phase for you to choose
Description:
This Wind Charge Controller is made of high quality material for long durability and stable performance. It is used for protecting the wind generator and prevent the battery from overcharging.
Specification:
Condition: 100% Brand New
Shell Material: Aluminum + Epoxy Resin
Color: Black
Type: Single Phase, Three Phase(Optional) For Single Phase
Rated Power: 300W
Battery Rated Voltage: DC 12V
Controller Output Current: ≥15A
Controller Output Voltage: 14.2±0.3V
Start Braking Voltage: 14.5±0.5V
Recover Charging Voltage: 13.5±0.5V
Weight: approx. 121g
Connection Method: 2 yellow wires are connected to wind turbine generator, red wire for battery positive pole, green wire for battery negative pole.
For Three Phase
Rated Power: 300W
Battery Rated Voltage: DC 12V
Controller Output Current: ≥10A
Controller Output Voltage: 14.2±0.3V
Start Braking Voltage: 14.2±0.5V
Recover Charging Voltage: 13.5±0.5V
Weight: approx. 247g
Connection Method: 3 yellow wires are connected to wind turbine generator, red wire for battery positive pole, black wire for battery negative pole.
Package Included:
1 x Wind Turbine Generator Charge Controller
Wind Turbines Generator Charge Controller Wind Regulator Rectifier 24v 600w
Battery voltage: 24V
Rate power: 600w
Started Braking voltage: 30V
Recovered Braking Voltage: 27V
Connection method:
AC in: connect the wind turbine to three green cables
DC out: connect the black cable to the negative pole of battery; connect the red cable to the positive pole of battery
Package includes:1x Wind Turbines charging controller
Dual 3 Phase Brake Switch for 2000 Watt Wind Turbines
- Dual 3 phase wind turbine brake switch (each switch will handle 2500 watts continuously)
- Two 90 amp bridge rectifiers
- Heavy-duty electro-galvanized steel recessed back plate
- Quick connects for fast setup
- All pre-wired and ready to go!
Perfect for our Freedom II 2000 Watt PMGs or two individual turbine installations, this 3-phase switch uses a specialized switch to provide both disconnect capability as well as braking by shorting out the 3 wires of the stator.
Although designed specifically for 3-phase turbines it works equally well for single phase AC turbines as well as DC turbines.
Features quick connects for easy connection from the wind turbine
Steel box enclosure for dual brake switches
Pre-wired connections from brake switches to rectifiers
Comes with instructions
Fully assembled and quality tested in the USA using global parts
AZN.M1.0
Yosoo Wind Charge Controller for Wind Turbine Generator 400W Waterproof 12V 24V Wind Turbine Generator Charge Controller (12v)
- Design. This Wind Generator Charge Controller is designed with auto-brake and manual brake function
- 3 yellow wires are connected to wind turbine generator, red wire for battery positive pole, black wire for battery negative pole
- Wind Generator Running Indicator: Green Light(always bright) indicates normal operation; Green Light(flashing) indicates charging; Red Light(Always bright) indicates auto brake state; Manual brake indicator: Red(Always bright) indicates manual brake state; Manual brakes must be manually restored
- To control the wind turbine generator battery charge automatically
- Protect the wind generator and prevent the battery from overcharging
Description:
This Wind Turbine Generator Charge Controller is well designed with auto-brake and manual brake function. It can be used to protect the wind generator and prevent the battery from overcharging. It can control the wind turbine generator battery charge automatically.
Specification:
Condition: 100% Brand New
Material: Plastic
Color: Black
Rated Output Power: 400W
Battery Voltage: 12V / 24V(Optional)
Weight: approx. 242g
Indicator Status:
Wind generator running indicator: Green Light(always bright) indicates normal operation
Green
Light(flashing) indicates charging Red Light(Always bright) indicates auto brake state
Manual brake indicator: Red(Always bright) indicates manual brake state
Manual brakes must be manually restored.
Package Included:
1 x Wind Turbine Generator Charge Controller
AZN.M1.0
Missouri Wind and Solar Freedom II PMG 12/24 Volt Permanent Magnet Wind Turbine Generator
- NO COGGING, easy to turn – Cut in speed of 6 MPH
- Skewed stator core with high grade electrical steel and heavy duty copper windings
- 17 mm stainless steel shaft compatible with all Missouri Wind and Solar hubs
- 2x thick polished aluminum case
- Fits delco bolt patterns and mounts up to our standard mounting bracket
If you are using the PMG on a 12 volt system choose the 12/24v model. For 24 volt systems use 24/48v model. For 48 volt systems use the 48/96v model.
Our Freedom II PMG permanent magnet generator is specifically designed for wind turbine use and can even be used with vertical axis wind turbines (VAWT).
Operating Information:
Produces battery voltage at approximately 266 RPM in parallel; 133 RPM in series
Produces twice (2x) the battery voltage at approximately 506 RPM in parallel; 253 RPM in series
Produces four times (4x) the battery voltage at approximately 960 RPM in parallel; 480 RPM in series
This permanent magnet generator works best with our 9 Blade Raptor Generation 4 blades and hub or our new Falcon Mach 4 80″ 3 blade set.
Why buy a Freedom or Freedom II PMG over a Delco car alternator PMA? The answer is more copper. Copper equals more power – each Freedom PMG stator contains twice as much copper than a Delco style PMA. Some modified alternators use power to make power. Freedom PMGs use no input power. PMAs use a thin aluminum housing and the stator is not pressed in.
The Freedom PMG features a very thick aluminum housing and a pressed in stator that helps with proper alignment and durability. PMAs have only two mounting holes. The Freedom PMG has four of them bolted tightly against the mounting bracket for secure mounting. Alternators and some PMAs have a weak rear bearing. The Freedom PMG utilizes two heavy duty bearings. Most car alternators and PMAs that are re-purposed use low grade/high iron electrical steel which can create a lot of heat. The Freedom PMG uses high grade electrical steel and is optimized for efficient cooling
PMG Features: Comes with two heavy duty rectifiers & one hub spacer stabilizer
Zinc plated 28 rare earth neodymium magnet rotor
For charging 12, 24, or 48V battery banks
Missouri Wind and Solar Freedom II PMG 24/48 Volt Permanent Magnet Wind Turbine Generator
- NO COGGING, easy to turn – Cut in speed of 6 MPH
- Skewed stator core with high grade electrical steel and heavy duty copper windings
- 17 mm stainless steel shaft compatible with all Missouri Wind and Solar hubs
- 2x thick polished aluminum case
- Fits delco bolt patterns and mounts up to our standard mounting bracket
If you are using the PMG on a 12 volt system choose the 12/24v model. For 24 volt systems use 24/48v model. For 48 volt systems use the 48/96v model.
Our Freedom II PMG permanent magnet generator is specifically designed for wind turbine use and can even be used with vertical axis wind turbines (VAWT).
Operating Information:
Produces battery voltage at approximately 266 RPM in parallel; 133 RPM in series
Produces twice (2x) the battery voltage at approximately 506 RPM in parallel; 253 RPM in series
Produces four times (4x) the battery voltage at approximately 960 RPM in parallel; 480 RPM in series
This permanent magnet generator works best with our 9 Blade Raptor Generation 4 blades and hub or our new Falcon Mach 4 80″ 3 blade set.
Why buy a Freedom or Freedom II PMG over a Delco car alternator PMA? The answer is more copper. Copper equals more power – each Freedom PMG stator contains twice as much copper than a Delco style PMA. Some modified alternators use power to make power. Freedom PMGs use no input power. PMAs use a thin aluminum housing and the stator is not pressed in.
The Freedom PMG features a very thick aluminum housing and a pressed in stator that helps with proper alignment and durability. PMAs have only two mounting holes. The Freedom PMG has four of them bolted tightly against the mounting bracket for secure mounting. Alternators and some PMAs have a weak rear bearing. The Freedom PMG utilizes two heavy duty bearings. Most car alternators and PMAs that are re-purposed use low grade/high iron electrical steel which can create a lot of heat. The Freedom PMG uses high grade electrical steel and is optimized for efficient cooling
PMG Features: Comes with two heavy duty rectifiers & one hub spacer stabilizer
Zinc plated 28 rare earth neodymium magnet rotor
For charging 12, 24, or 48V battery banks
Missouri Wind and Solar 1600 Watt 5 Blade Missouri Freedom Wind Turbine (24V, Black)
- 5 High Quality Raptor Generation 4 Blades – Self Regulating Blades
- 1600 Watt, High Amp Freedom Permanent Magnet Generator (PMG) with skewed stator core for no-cogging!
- A Missouri Wind and Solar Freedom PMG has more copper for more power! Our Freedom PMG contains twice as much copper than any Delco style PMA
- Also comes with: Stars & Stripes tail, steel hub, rectifier, heavy duty hub spacer/stabilizer, stainless steel nuts and bolts for assembly.
It has a 14 magnet rotor inside and our skewed stator core for easy turning – up to 1600 watts max output! NO COGGING – Cut in speed of 6 MPH
This unit comes with:
Freedom PMG (PERMANENT MAGNET GENERATOR) WITH 14 MAGNET ROTOR.
Freedom PMG has no brushes, very dependable!
125,000 hours + of rated bearing life.
One heavy duty bridge rectifier for converting 3 phase to DC output.
Fully galvanized mounting Bracket and Heavy Duty two arm tail assembly.
Tail fin measures 29″ tall for maximum tracking.
No slip rings to fail or replace. Wire tension system.
Comes with 5 Raptor Generation 4 nylon carbon fiber composite blades.
Aerodynamically tapered Genuine RAPTOR GENERATION 4 Blades for maximum output.
Blades Make 62 1/2″ dia. swept area
Steel blade hub is 1/4” thick x 9” in diameter
Mounting Bracket Fits on 1.5″ schedule #40 or #80 pipe.
Heavy duty Hub spacer/stabilizer
Turbine Weight: 38.4 pounds
Shipping Weight: 40 pounds
Shipping Dimensions: 30″ x 10″ x 8″
Our Freedom PMG permanent magnet generator is specifically designed for wind turbine use and can even be used with vertical axis wind turbines.
PMG Features:
17 mm Stainless steel shaft compatible with all Missouri Wind and Solar hubs
Polished aluminum case
Zinc plated 14 magnet rotor and skewed stator core
Fits delco bolt patterns and mounts up to our standard mounting bracket.
PMG Specifications:
3/8″ Diameter bolt holes
1 15/16″ on center between mounting holes 5 7/8″ OD Width 6 5/16″ Tall (Can be used as 3 phase output or DC output / Grid tie or battery charging)
2000 Watt 11 Blade Missouri General Freedom II Wind Turbine
- Metal components are fully hot dipped galvanized, hub is zinc plated – Will not rust – No need for painting or special coating for up to 50 years under normal conditions
- Raptor carbon fiber blades withstand 125 mph – Guaranteed for a lifetime, not to break under normal use.
- The permanent magnet generator has a 28 rare earth magnet rotor inside and our skewed stator core for easy turning – up to 2000 watts max output!
- The Missouri Freedom II Wind Turbines have a cut-in wind speed of 6 MPH and NO COGGING!
- Each Freedom PMG rotor contains twice as much copper than any Delco style PMA – more copper means more power!
This unit comes with:
Freedom ll PMG (PERMANENT MAGNET GENERATOR) WITH 28 MAGNET ROTOR
Freedom ll PMG has no brushes, very dependable
125,000 hours + of rated bearing life
Two heavy duty bridge rectifiers for converting 3 phase to dc output
Mounting Bracket and Heavy Duty 2 arms tail assembly
Tail fin measures 29″ tall for maximum tracking
No slip rings to fail or replace. Wire tension system
Comes with 11 Raptor nylon carbon fiber composite blades
Aerodynamically tapered Genuine RAPTOR GENERATION 4 Blades for maximum output
Blades Make 62 1/2″ dia. swept area
Steel blade hub is 1/4” thick x 9” in diameter
Mounting Bracket Fits on 1.5″ schedule #40 or #80 pipe
Heavy duty Hub spacer/stabilizer
3 YEAR Limited WARRANTY
Turbine Weight: 50 pounds
Shipping Weight: 55 pounds
Shipping Dimensions: 30″ x 10″ x 8″
Manufactured in the USA
PMG Features:
NO COGGING – CUT-IN SPEED IS 6 MPH
17 mm Stainless steel shaft compatible with all Missouri Wind and Solar hubs
Polished aluminum case
Zinc plated 28 magnet rotor and skewed stator core
For charging 12, 24, or 48 volt battery banks
Specifically designed for wind turbines
AZN.M1.0
MWANDS.COM, LLC 1600 Watt 7 Blade Missouri Freedom 3 Sealed Wind Turbine (Black)
- Fully sealed to create a water-resistant motor for wind and hydropower. Perfect for marine environments but can be used anywhere a wind turbine can be mounted.
- Water-resistant design… No marine varnish or painting required! Fully sealed 1600 watt Freedom 3PMG with labyrinth style sealed front bearing and gasket style seal to keep water from seeping into the case.
- PMG also features 17mm shaft, custom hub spacer/stabilizer with keyway, and zinc-plated 14 rare earth neodymium magnet rotor.
- PMG mounting braket and stars & stripes turbine tail are hot-dipped galvanized for a weather-resistant finish. Tail is cut from 16 gauge steel for added durability!
- Turbine Kit Includes: Freedom III Fully Sealed PMG, PMG mounting bracket, turbine tail, spacer/stabilizer, rectifier, and seven G4 blades.
Freedom 3 Sealed PMG – For Land or Sea
The Missouri Wind and Solar Freedom 3 PMG is fully sealed to create a water-resistant motor for wind and hydropower. Truly well thought out with years of R&D behind the production. The fully sealed motor is perfect for marine environments but can be used anywhere a wind turbine can be mounted.
Wind Turbine Features:
♦ Fully Sealed 1600 Watt Freedom 3 PMG with 3 phase bridge rectifier
♦ Heavy duty hub spacer/stabilizer with slot to fit keyway
♦ PMG mounting bracket and heavy-duty Stars & Stripes wind turbine tail
– Mounting Bracket fits on 1.5″ schedule #40 or #80 pipe (1 7/8″ OD) and allows for easy turning
– Tail fin measures 9 3/4 inches wide x 28 3/4 inches tall (Cut from 16 gauge steel) – Hot dipped galvanized weather resistant finish
♦ Includes 7 Generation 4 aerodynamically tapered carbon fiber composite blades
Fully Sealed Freedom 3 PMG Features:
♦ Larger bearings to withstand wear and abuse
♦ Sealed front bearing with additional labyrinth style seal
♦ Case with a rough, natural finish means more surface area to speed
♦ Keyed shaft and hub stabilizer
♦ Hub stabilizer that channels water away from entering through the front of the housing
♦ Gasket style RTV seal to keep water from seeping into the case
♦ Water resistant design – no marine varnish or painting required
♦ Wind tunnel testing up to 55 MPH
Freedom PMG Features:
♦ 17 mm stainless steel shaft
♦ Custom hub spacer/stabilizer with keyway and bolts for securely attaching to Missouri Wind & Solar hubs
♦ Double Nickel and Zinc plated powerful 14 rare earth neodymium magnet rotor
♦ No brushes to fail or replace
♦ Large, heavy-duty bearings in front and back
♦ Fits Delco bolt patterns and mounts up to our standard mounting bracket
♦ 3/8″ Diameter bolt holes
♦ 1-15/16″ on center between mounting holes
♦ 5-7/8″ OD Width
♦ 6-5/16″ Tall